SCOUTPARTS.COM stocks 1961-1980 International Harvester Scout 80, 800, 800A, 800B, Scout II, Terra and Traveler parts. We sell used Scout parts as well as common upgrades such as disc brake conversion kits, lift kits, fuel injection kits, offroad steering upgrades and roll bars. We're the best source for complete clutch kits, custom wiring harnesses, and gas tanks. We offer a full line of restoration and performance parts including Light Line original IH parts. We stock hard to find used, new and NOS (new old stock) parts. Both the Scout specialist and the new IHC enthusiast can count on us to find the Scout parts they need. As Scout owners, we drive Scouts and understand the needs of the 4x4 binder enthusiast and restoration customer alike. We have more parts listed on our site than anyone else on the internet and if we don't have it listed we can still probably get it. If you're looking for International Scout parts, you've found the right place.
These are new shifter decals for your Scout 80s and Scout 800s with 3 speed transmissions.
|
Our Price: $12.59
|
Gasket that goes on the top of your Scout 80, Scout 800 gas tank. Need one per gas tank. This gasket is only used on original metal fuel tanks.
|
Our Price: $11.09
|
This is a tail light lens gasket set for the round tail lights used on Scout 80 & 800 and on Travelalls and pickups. See SP10541 for a picture of the lens these mate with.
Each kit contains an inner and an outer gasket required to seal your lens against the weather. These prevent water, dust, an
|
Our Price: $7.97
|
these are the real deal!! Dash board light bulb sockets. Lights up heater, head light and wiper indicators, gauges, speedo. fits all IH trucks and Scouts!!
|
Our Price: $4.64
|
This is a complete set of 9 new LED lights to replace your old incandescent bulbs. You know, the ones that seem to only burn out when you are giving a ride to your mother in-law that does not quite like you...yet.
SPEEDO:
2 Illumination LEDs
2 Turn Signal
1 4x4 Engage
1 E-brake
1 Brights
ALT/FUEL:
|
Our Price: $32.29 set of 9 bulbs
|
These are new replacement bulbs for Scout 800 instrument gauges.
|
Our Price: $1.22
|
Easy to install - NO soldering MUST BE GROUNDED!
If your gauges are reading incorrectly or not at all, you may need this brand new high capacity solid state regulator kit. It replaces the old mechanical one behind your Oil/Temp gauge. NO MOVING PARTS! This regulator has a capacity far beyond the
|
Our Price: $58.42
|
***Notice these mounts do not have every curve and bend that the original ones do***
Don't be fooled by imitations. This is the only kit on the market that is engineered to address all 9 points of contact. These are not shock bushings repackaged. This is a kit with all the washers, bolts, and lock
|
Our Price: $149.04 working on new batch
|
Upper windshield frame seal that goes between frame and top.
|
Our Price: $80.16
|
A lot of Scouts have a tapping sound in the engine from noisy or sticking lifters. These brand new lifters are correct for the following engines:
152CI 4 cylinder
196Ci 4 cylinder
266CI 6 cylinder
304Ci 8 cylinder
345CI 8 cylinder
392CI 8 cylinder
|
Our Price: $25.79
|
Brand new steering column to firewall seal, made to the exact specifications used for the original seals.
|
Our Price: $34.37
|
Rear axle outer oil seal scout 80 Dana 27.
|
Our Price: $28.52
|
This oil pan gasket fits the 4 and 8-cylinder motors used in Scouts, trucks, Travelalls, and Metro. Do DEQ a favor and fix that oil leak today!
|
Our Price: $34.48
|
New replacement cable. This cable comes in a 12'length and can be cut to fit. It is a 1/4" housing and the throw length(pulling on the knob)is up to 2" This cable will work as a replacement for a choke, hood release, throttle(pto applications), vent cable, or any other application you might need.
|
Our Price: $27.52
|
Tail light wiring harness (pigtail) for tail bulb sockets.
|
Our Price: $6.53
|
Rear main crankshaft seal for international-built V8 and 4-cylinder engines
|
Our Price: $71.01
|
We now have brand new shifter knobs to fit Scout 80, Scout 800, and pickups and Travelalls. This was used on 3 and some 4-speed transmissions used in C, K, KB, M, L, R, S, A, B, and C-series trucks.
Made of phenolic rubber like the original, This has a 3/8" SAE (fine) thread. If this is not c
|
Our Price: $28.67
|
The later Scout II trucks with the plastic tail light housings use this replaceable lamp socket. This is the lower of the two sockets, accepts a single contact reverse bulb, and is a direct replacement for you worn or rusted socket.
|
Our Price: $17.16
|
***You are ordering the pin pictured, if you want the slave cylinder order sp11773***
Fits Scout 80 and 800 with hydraulic clutches, extra heavy duty service. Clutch Slave Cylinder actuator pin. This part was made 3/16 longer than original equipment. Specifically manufactured for the customers with
|
Our Price: $51.58
|
Fuel filter, small glass bowl type for early scouts & trucks.
|
Our Price: $17.20
|
All Scout II vehicles use this tail lamp housing gasket between the metal or plastic (depending on year) housing and the body. Without this gasket the tail lamp housing fills with water, the contacts corrode, and eventually the bulb fails.
|
Our Price: $14.32
|
Brand-New IH Scout II Accelerator / Throttle Cable Part. This cable is 28-5/8" end to end.
This is the REAL DEAL IH Part. part 440983C1
To fit the 1973-1978 Scout II with 304 / 345 V8.
This cable has a socket fitting on the carburetor end, and a ball on the gas pedal end that fits into
|
Our Price: $60.06
|
Scout 80/800 door check straps made as exact replicas of the factory part. Available in black, and look great on any door. Sold Each.
|
Our Price: $17.20
|
So close to original that it\'s difficult to tell the difference. Many states do not require a front plate. Because of this, we have deleted the holes for the license plate.
Same original thickness and original mounting holes. Super close reproduction of factory original.
In stock now.
Fits bot
|
Our Price: $400.38 working on new batch
|
|
Our Price: $1.40
|
These are new plastic fan shrouds for Scout II. These are designed for use with V8 engines, and they will fit 4-cylinder motors too. These may or may not work with the inline engines (258, SD-33). If you have one of those engines, call us anyway to make sure.
|
Our Price: $177.77
|
Stainless steel bolt kit for your rear bumper. Holds your rear bumper on and will not rust and freeze up. A must for any restoration.
Made in the USA
|
Our Price: $10.27
|
If you have a 4 cylinder Scout 80, 800 there's a good chance you may need one of these. They tend to have gotten rusty and weak in the last 40 years.
|
Our Price: $21.17
| |
